---
title: "Janome Embroidery Machine Troubleshooting: MB-4S and MB-7 Error Codes, Thread Breaks and Fixes"
description: "Janome embroidery troubleshooting for MB-4S, MB-7, Continental M17 and Memory Craft: E:00 to E:09 error codes, warning signs, thread breaks and hoop fixes."
url: https://easydigitizer.com/troubleshooter/janome
updated: 2026-10-14
brand: Janome
class: both
origin: Japan
formats: JEF (native), JEF+, JPX, DST
data: https://easydigitizer.com/troubleshooter/data.json
agent_playbook: https://easydigitizer.com/troubleshooter/agent.md
publisher: EasyDigitizer (https://easydigitizer.com/)
---

# Janome embroidery machine troubleshooting

Janome embroidery troubleshooting for MB-4S, MB-7, Continental M17 and Memory Craft: E:00 to E:09 error codes, warning signs, thread breaks and hoop fixes.

> **Short answer:** Most Janome embroidery stops come down to three things: a needle thread that missed the tension discs or thread holder, lint or thread jammed in the hook area, and a needle that is bent, blunt or not pushed fully up. On the MB-4S and MB-7 the code you will see most is **E:05** (needle thread broke or ran out); on Memory Craft and Continental machines it is the **overload** warning, which clears after about 15 seconds once you remove tangled thread from the hook and cutter area.

## Model families
### MB-4S / MB-4Se / MB-4 (4-needle)
- **Type:** Semi-commercial single-head, 4 needles
- **Years:** MB-4 from about 2009; MB-4S and MB-4Se current
- **Field:** 240 × 200 mm (MB hoop M1)
- **Max speed:** 800 spm (adjustable from 400 in 100 spm steps)
- **Panel:** RCS remote computer screen (LCD touch panel) on a cable
- **Formats:** JEF, JEF+, DST
- **Manual:** [MB-4S instruction book (PDF)](https://janome.com/wp-content/uploads/2024/09/inst-book-mb4seng.pdf)
- **Tags:** multi-needle, 4-needle, tajima-hoops, semi-commercial
The MB-4 family is a compact four-needle machine with a free-arm style bed that also accepts optional Tajima-style round hoops and Janome cap, sock and monogram hoops. It shows short numbered codes (E:00 to E:09) on the RCS. Typical failure points are lint in the hook race, a dry needle bar, false thread-break stops from an over-sensitive sensor, and needle-bar change problems if the head is forced or not oiled. After 1,000 motor hours the machine asks for a DC motor replacement.

### MB-7 (7-needle)
- **Type:** Semi-commercial single-head, 7 needles
- **Years:** about 2014–present
- **Field:** 240 × 200 mm (M1 hoop, about 9.4 × 7.9 in)
- **Max speed:** 800 spm
- **Panel:** 5.7-inch RCS remote computer screen
- **Formats:** JEF+, JEF, DST
- **Manual:** [MB-7 instruction book (PDF)](https://janome.com/wp-content/uploads/2024/09/inst-book-mb-7.pdf)
- **Tags:** multi-needle, 7-needle, tajima-hoops, semi-commercial
The MB-7 is the seven-needle big brother of the MB-4S, with an extra-large bobbin, a separate bobbin-winding motor and the same RCS screen. Its error list matches the MB-4S and adds a thread-catcher motor initialisation error and an "embroidery area exceeds the hoop" message. Janome asks for daily oil on the hook race and needle-bar oil about every two weeks under frequent use.

### Continental M17
- **Type:** Home/prosumer sewing and embroidery combination, single needle
- **Years:** 2021–present
- **Field:** 280 × 460 mm (RE46d hoop)
- **Max speed:** 1,200 spm in embroidery (set from 400 in 100 spm steps)
- **Panel:** Two touch screens, wireless LAN
- **Formats:** JEF, JEF+, JPX, DST
- **Manual:** [Continental M17 embroidery instruction book, part 1 (PDF)](https://www.janome.ca/wp-content/uploads/2025/02/insml-cm17_emb-eng-part-1.pdf)
- **Tags:** combo, large-field, wifi, magnetic-hoop
Janome's flagship combo machine. It ships with SQ10d, RE20d, SQ28d, RE46d and the ASQ27d quilting hoop with magnetic clamps. Most "faults" are overload stops from thread wrapped around the cutter, a needle plate that is not clicked into its set position, or a USB stick formatted the wrong way. Cleaning reminders for the bobbin holder appear on a timer and can be switched off in settings.

### Memory Craft 550E / 500E (embroidery only)
- **Type:** Home embroidery-only, single needle
- **Years:** 500E about 2014, 550E about 2016–present
- **Field:** 200 × 360 mm (RE36b hoop)
- **Max speed:** 860 spm (adjustable from 400; the default is 600)
- **Panel:** Colour touch screen
- **Formats:** JEF, JEF+, JPX, DST
- **Manual:** [Memory Craft 550E instruction book (PDF)](https://www.janome.com/wp-content/uploads/2019/11/inst-mc550e_le.pdf)
- **Tags:** embroidery-only, large-field, home
These are dedicated embroidery machines with a large carriage and hoops SQ14b, RE20b, SQ20b and RE36b. The RE36b hoop needs the clamps and anti-slip sticker and Janome recommends staying at the default 600 spm with it. Common issues are distortion from running the big hoop too fast, overload stops from thread in the hook, and the bobbin winder left in the winding position. The 550E has a built-in hoop calibration routine and owner oiling points (needle bar, wick, lower shaft, X and Y carriage).

### Skyline S9
- **Type:** Home sewing and embroidery combination
- **Years:** about 2017–present
- **Field:** 170 × 200 mm (RE20a hoop)
- **Max speed:** 800 spm in embroidery
- **Panel:** Colour touch screen, app connectivity
- **Formats:** Janome JEF family (check the instruction book for the full list)
- **Manual:** Instruction book ships with the machine; contact a Janome dealer for a copy
- **Tags:** combo, home, wifi
A mid-size combo with RE20a, SQ14a and FA10a hoops and a 200,000-stitch-per-design limit. Problems are usually the same as other Janome home machines: thread not seated in the take-up lever, lint under the needle plate, a design larger than the hoop selected, or a USB stick the machine cannot read.

### Memory Craft 9850 / 11000 / 12000 / 14000 / 15000 and Memory Craft 400E
- **Type:** Home sewing and embroidery combinations (400E is embroidery-only)
- **Years:** 2000s to 2010s
- **Panel:** Touch screen (size varies by model)
- **Formats:** JEF (some also read DST)
- **Manual:** Not hosted publicly by Janome for every model; ask an authorised Janome dealer
- **Tags:** combo, older, home
Older Janome combo machines share the same embroidery logic as the current range: overload stops, hoop-not-attached and design-too-large messages, and thread-break stops. Janome did not publish a numbered code list for these models that we could verify, so use the symptom guide below. Elna embroidery machines are built by Janome and share many mechanisms, so the same symptom fixes usually apply.

## Error codes
| Code | Message | Meaning | Fix | Models | Source |
|---|---|---|---|---|---|
| E:00 | Communication error with the RCS | The machine and its remote screen are not talking; the screen may also hang on the welcome page. | Switch off, check the RCS cable is fully seated at both ends, switch on again. If it keeps happening, a dealer can test with a spare RCS unit. | MB-4S, MB-4, MB-7 | MB-4S and MB-7 instruction books; Sii Store dealer blog for cable checks |
| E:01 | Initializing error | One of the stepping motors (hoop, needle-bar change, cutter or catcher) did not find its home position at start-up. | Switch off, remove anything blocking the carriage or hoop, switch on again. If it repeats, note which part does not move at start-up and call a technician. | MB-4S, MB-4, MB-7 | MB-4S instruction book; Sii Store dealer blog (code number) |
| E:02 | Needle bar switching error | The head could not move to the requested needle bar. | Switch off and on. Check nothing is caught between the needle case and the frame. If it binds when moved by hand, the head play needs a technician. | MB-4S, MB-4, MB-7 | MB-4S instruction book; Sii Store dealer blog (code number) |
| E:03 | Needle bar stop position error | The needle bar stopped out of its switching position. | Press ENTER to let the machine reset the needle bar position. If it comes back, call a technician. | MB-4S, MB-4, MB-7 | MB-4S instruction book; Sii Store dealer blog (code number) |
| E:04 | Driving motor overload | The main motor stopped because it was overloaded, usually by jammed thread. | Wait about 15 seconds for the ready screen, then remove tangled thread from the hook, take-up area and cutter. Turn the handwheel by hand to confirm it moves freely. | MB-4S, MB-4, MB-7 | MB-4S instruction book; Sii Store dealer blog (code number) |
| E:05 | Needle thread broke or ran out | The upper thread sensor stopped seeing thread movement. | Press MODE, rethread the needle with the presser foot up, and restart. If it stops with good thread, lower the thread-break sensitivity (higher stitch count). | MB-4S, MB-4, MB-7 | MB-4S instruction book; Sii Store dealer blog (code number) |
| — | Needle bar setting error | The needle bar number for a colour is missing or not valid. | Press MODE to return to the ready screen and assign a needle bar to every colour in the design. | MB-4S, MB-7 | MB-4S and MB-7 instruction books (code number not published) |
| E:07 | Auto thread cutting error | The thread cutter did not complete its cycle. | Switch off and on. Clear thread wrapped around the cutter and catcher under the needle plate. If it repeats, the cutter needs a technician. | MB-4S, MB-4, MB-7 | MB-4S instruction book; Sii Store dealer blog (code number) |
| E:08 | Tension discs opened while stitching | The tension release lever was opened during sewing. | Close the tension release lever; the ready screen returns. | MB-4S, MB-4, MB-7 | MB-4S instruction book; Sii Store dealer blog (code number) |
| E:09 | Upper shaft stop position error | The main shaft did not stop in its expected position. | Switch off and on. If it repeats, the motor or shaft sensor needs a technician. | MB-4S, MB-4, MB-7 | MB-4S instruction book; Sii Store dealer blog (code number) |
| — | Thread catcher motor initializing error | The thread catcher motor did not find its home position. | Press ENTER to initialise the motor again. Clear any thread around the catcher if it repeats. | MB-7 | MB-7 instruction book |
| — | Embroidery area exceeds the hoop | The design is larger than the hoop type selected. | Press ENTER, then select the correct hoop or resize or move the design. | MB-7 | MB-7 instruction book |
| — | Replace the DC motor | The main motor has reached 1,000 running hours. | Book the machine with your dealer for a motor change before it fails. | MB-4S | MB-4S instruction book |
| — | Machine stops due to overload | The motor stopped because thread or debris is jamming it. | Wait at least 15 seconds, then clear tangled thread around the take-up lever, hook race and automatic cutter before restarting. | Continental M17, MC 550E | M17 and MC 550E instruction books |
| — | Start/stop pressed with foot control connected | Embroidery cannot be started from the button with the foot control plugged in. | Unplug the foot control and use the start/stop button. | Continental M17 | M17 instruction book |
| — | Needle plate removed or not set | The needle plate is off, not clicked down, or was released with the emergency dial. | Press the plate down until it snaps in. If the release dial was used, turn it back to the set position first. | Continental M17 | M17 instruction book |
| — | Feed dogs lowered | The machine was started with the feed dogs down. | Raise the feed dogs unless you meant to sew with them down. | Continental M17 | M17 instruction book |
| — | Twin needle warning | Twin needle mode is active. | Fit a single needle and confirm with OK. | Continental M17 | M17 instruction book |
| — | Bobbin winder spindle shifted | The bobbin winder is still in the winding position. | Push the bobbin winder spindle back to the left, then stitch. | MC 550E | MC 550E instruction book |
| — | Lockout with hoop in the way | The lockout key was pressed while the hoop blocks threading. | Press OK; the hoop moves aside so you can thread. | MC 550E | MC 550E instruction book |
| — | Machine malfunction | The control system found a fault it cannot clear. | Switch off and on once. If the sign comes back, stop and contact your Janome service centre. | MC 550E | MC 550E instruction book |
| — | Clean bobbin holder | Timed reminder to remove lint from the bobbin holder. | Clean the bobbin holder and hook race, then confirm. The reminder can be turned off in settings. | Continental M17, MC 550E | M17 and MC 550E instruction books |

## Common problems and fixes
### Upper thread keeps breaking (E:05)
**Symptoms:** thread, tension, needle
**Likely causes:** thread missed the tension discs or take-up lever, thread not set in the thread holder at the start, tension too tight, damaged needle, very dense design
1. Raise the presser foot (or open the tension on MB models) and rethread the whole path so the thread drops into the tension discs and through the take-up lever.
2. Put a new needle in, flat side to the back, pushed fully up, and tighten the clamp screw.
3. On M17 and 550E, set the thread end in the thread holder before you press start.
4. Lower the upper tension a step and test on scrap with the same fabric and stabilizer.
5. Use quality 40 wt embroidery thread; if a dense design still shreds, reduce its density in your software.
**Call a technician if:** breaks continue with new thread and a new needle and you can feel a burr on the needle plate hole or hook point.

### Machine stops for a thread break that did not happen
**Symptoms:** sensor, thread
**Likely causes:** thread-break sensor too sensitive (MB), short stitches, lint in the thread path
1. On MB-4S and MB-7, raise the thread-break stitch count (range 3 to 16; higher means less sensitive).
2. Turn on "ignore short stitches" so stitches under the set length (up to 1.0 mm) are dropped.
3. Clean lint and wax from the tension area with a folded piece of paper.
**Call a technician if:** false stops continue with the sensor at its least sensitive setting.

### Birdnest under the fabric
**Symptoms:** birdnest, looping, tension
**Likely causes:** upper thread not in the tension discs, fabric loose in the hoop, embroidery foot caught on a jump thread, foot height too high
1. Stop, cut the nest free from underneath, and remove the hoop without forcing it.
2. Rethread the upper thread with the presser foot up so it seats in the tension discs.
3. Rehoop drum-tight with a stabilizer that suits the fabric.
4. On M17, adjust the embroidery foot height so it does not ride over thread clumps.
5. Clean the hook race before restarting.
**Call a technician if:** nests continue with correct threading and the machine makes a clicking or knocking noise.

### Bobbin thread breaks or bobbin shows on top
**Symptoms:** bobbin, tension
**Likely causes:** bobbin not threaded through the bobbin holder spring, lint in the holder, nicked bobbin or bobbin case, upper tension too tight
1. Take out the bobbin and reinsert it so it turns the correct way and the thread runs through the spring slot.
2. Brush lint from the bobbin holder and hook race.
3. Swap to a new bobbin if the old one is scratched or does not spin smoothly.
4. Loosen the upper tension one step and test.
**Call a technician if:** the bobbin case has a burr or crack you cannot replace yourself.

### Needle breaks
**Symptoms:** needle
**Likely causes:** needle not fully inserted, loose clamp screw, needle too fine for the fabric, hoop hitting something, wrong hoop selected
1. Fit a new needle of the right size, pushed fully up with the flat side back, and tighten the screw.
2. Check that the hoop selected on screen matches the hoop on the machine.
3. Clear the space around the machine so the carriage cannot hit a wall or object.
4. On MB machines, use the DB x K5 type needle the manual specifies.
**Call a technician if:** needles keep breaking in the same spot or the needle hits the plate when you turn the handwheel slowly.

### Design distorted or out of registration
**Symptoms:** registration, puckering, hoop
**Likely causes:** fabric not tight in the hoop, no stabilizer, carriage bumping into something, speed too high with large hoops
1. Rehoop tightly and add a stabilizer suited to the fabric.
2. Make sure the hoop is locked in the carriage and nothing is near the moving arm.
3. Lower the speed: on the 550E stay at 600 spm with the RE36b hoop.
4. Trim long jump threads that the foot could catch.
**Call a technician if:** a test pattern is still misaligned after hoop calibration.

### Design is off-centre (hoop calibration)
**Symptoms:** hoop, frame, registration
**Likely causes:** hoop centre position drifted, hoop not seated
1. On the 550E, open settings and run hoop calibration; the carriage moves to centre and you match the needle to the template.
2. Seat the hoop firmly so both pins lock in the carriage.
3. Use the jog keys to fine-tune the start point before sewing.
**Call a technician if:** calibration will not hold after a restart.

### Thread cutter does not cut or causes overload
**Symptoms:** trimmer, motor
**Likely causes:** thread wrapped around the cutter, lint under the needle plate, cutter jammed
1. Remove the needle plate and brush lint from the cutter and catcher.
2. Pull out any thread wrapped around the hook and cutter.
3. On MB machines with E:07, switch off and on after cleaning.
**Call a technician if:** E:07 or overload stops continue after a full clean.

### USB stick not read
**Symptoms:** usb, file
**Likely causes:** wrong file system, damaged stick, unsupported file type
1. Format the stick on a Windows PC as FAT16 or FAT32, allocation unit 64 KB or smaller, with Quick Format unticked.
2. Save designs as JEF, JEF+ or DST.
3. Try a different, smaller USB stick.
**Call a technician if:** no stick works and the USB port looks damaged.

### DST design shows wrong colours
**Symptoms:** file, colour-change
**Likely causes:** DST files store no colour information
1. Assign colours or needle bars after loading; Janome fills in its own colours.
2. On MB machines, reserve colours for needle bars so you do not rethread between designs.
3. Save as JEF+ from your digitizing software to keep colours.
**Call a technician if:** not needed; this is a file format limit.

### Machine is noisy or loops
**Symptoms:** noise, oiling, looping
**Likely causes:** lint in the hook, lack of oil, thread jammed at the take-up lever
1. Brush out the hook race and feed area.
2. Oil the points the manual shows (MB: hook race daily, needle bars every two weeks with frequent use).
3. Turn the handwheel by hand to find any binding.
**Call a technician if:** a grinding or knocking noise remains after cleaning and oiling.

### Touch panel keys respond in the wrong place
**Symptoms:** display
**Likely causes:** key positions out of alignment
1. Run the touch screen calibration in settings.
2. Switch off and on if keys stop responding entirely.
**Call a technician if:** calibration fails or the screen stays blank.

## Maintenance schedule
| Interval | Task | Notes |
|---|---|---|
| Every bobbin change | Brush lint from the bobbin holder and hook race | Clean the auto cutter area too on M17 and 550E. |
| Daily (MB, frequent use) | One or two drops of oil in the hook race | Wipe off excess so it does not stain fabric. |
| Every two weeks (MB, frequent use) | Oil the needle bars through the holes in the front cover | Clip just the tip of the oiler nozzle. |
| Monthly | Clean under the thread guide plate and pre-tension (M17) | Brush out dust under the top cover. |
| Monthly (550E, daily use) | Oil needle bar, presser bar, take-up lever, wick, lower shaft, X and Y carriage felts | Move the carriage home and switch off first. |
| Every four months (MB, frequent use) | Oil crank rod, main shaft and Y-carriage bushings | Select needle bar 4 (MB-4S) or 7 (MB-7) to expose the points. |
| At 1,000 motor hours (MB-4S) | DC motor replacement | Dealer job; the machine shows a message. |
| Yearly | Dealer service: timing, cutter, tension check | Sooner if you run production hours. |

## Settings that cause stitch problems
- **Thread-break sensitivity (MB-4S, MB-7):** a low stitch count makes the machine stop for breaks that did not happen. Raise the value before you blame the thread.
- **Ignore short stitches:** if this is set high, small details and tie-ins disappear and the design looks gappy. If it is off, tiny stitches can shred thread.
- **Trim tail length:** a short tail can pull out of the needle after a trim, causing a false break or a missed first stitch. Try medium or long with thick thread.
- **Jump thread cutting length (M17, 550E):** a value that is too short makes the machine trim constantly and threads can bunch under stippling designs.
- **Maximum speed:** large hoops (RE36b, RE46d) and narrow satin stitches warp at high speed. Use 600 spm or less on big hoops.
- **Upper thread and bobbin sensors (M17):** if these are turned off, the machine keeps sewing after a break and you get blank areas.
- **Hoop selection:** choosing a bigger hoop on screen than the hoop on the machine lets the needle strike the frame.
- **Consecutive colour grouping:** merges same-colour sections; turn it off if you need the original stop order.

## Official manuals, FAQs and support
- [MB-4S instruction book (PDF)](https://janome.com/wp-content/uploads/2024/09/inst-book-mb4seng.pdf) — error messages, troubleshooting table, oiling points, thread-break sensor settings
- [MB-7 instruction book (PDF)](https://janome.com/wp-content/uploads/2024/09/inst-book-mb-7.pdf) — MB-7 error messages, audible signals, oiling schedule
- [MB-7 info sheet (PDF)](https://janome.com/wp-content/uploads/2024/01/mb7-info-sheet.pdf) — specifications, hoops, formats
- [Continental M17 embroidery instruction book, part 1 (PDF)](https://www.janome.ca/wp-content/uploads/2025/02/insml-cm17_emb-eng-part-1.pdf) — hoops, setup, embroidery functions
- [Continental M17 embroidery instruction book, part 2 (PDF)](https://www.janome.ca/wp-content/uploads/2025/02/insml-cm17_emb-eng-part-2.pdf) — settings, warning signs, troubleshooting, USB formatting
- [Memory Craft 550E instruction book (PDF)](https://www.janome.com/wp-content/uploads/2019/11/inst-mc550e_le.pdf) — warning signs, troubleshooting, hoop calibration, oiling
- [Skyline S9 product page (Janome Australia)](https://janome.com.au/product/skyline-s9/) — specifications and hoops

## Frequently asked questions
### What does E:05 mean on a Janome MB-4S or MB-7?
It means the machine thinks the needle thread broke or ran out. Press MODE, rethread with the tension open so the thread drops into the discs, and restart. If it stops again with good thread, raise the thread-break stitch count in settings.

### How do I clear E:04 on my Janome MB-4?
E:04 is a motor overload. Wait for the ready screen, switch off, and clear thread from the hook, take-up lever and cutter. Turn the handwheel by hand; if it will not turn freely, call a technician.

### What file format does a Janome embroidery machine use?
Janome's own format is JEF, with JEF+ as the editable version and JPX for files with a background image. Current machines also read Tajima DST, but DST carries no colour information, so you assign colours after loading.

### Why won't my Janome read my USB stick?
Most often the stick is formatted incorrectly. Format it on a Windows PC as FAT16 or FAT32 with a 64 KB or smaller allocation size and without Quick Format, then copy the designs again.

### Can I use Tajima hoops on a Janome MB-4S or MB-7?
Yes. The MB-4S lists optional Tajima round hoops from 34 mm to 142 mm and a 78 × 168 mm frame, and the MB-7 is sold as Tajima-hoop compatible. Select the Tajima hoop type on the RCS so the machine knows the limits.

### How often should I oil a Janome MB-7?
With frequent use, oil the hook race every day and the needle bars every two weeks. Oil the crank rod, main shaft and Y-carriage bushings every four months, and wipe off any excess.

### Does the Continental M7 embroider?
No. The Continental M7 is a sewing and quilting machine. For embroidery in that line, the Continental M17 is the combination model.

## Diagrams

- [Five-minute diagnosis](https://easydigitizer.com/troubleshooter/img/diagnose-flow.svg): Where to start when the machine stops or sews badly.
- [Upper thread path](https://easydigitizer.com/troubleshooter/img/thread-path.svg): Every guide from the cone to the needle eye — the fix for most breaks and nests.
- [Why birdnests happen](https://easydigitizer.com/troubleshooter/img/birdnest.svg): What a nest is, the usual causes in order, and how to clear one safely.
- [The I-test for tension](https://easydigitizer.com/troubleshooter/img/tension-test.svg): Read the back of a satin column to balance top and bobbin tension.
- [Bobbin drop test](https://easydigitizer.com/troubleshooter/img/bobbin-drop-test.svg): Set bobbin tension before you touch the top tension.
- [Needle orientation](https://easydigitizer.com/troubleshooter/img/needle-orientation.svg): Long groove to the front, scarf to the hook, pushed fully up.
- [Hook timing](https://easydigitizer.com/troubleshooter/img/hook-timing.svg): What correct hook-to-needle timing and clearance look like.
- [Presser foot height](https://easydigitizer.com/troubleshooter/img/presser-foot-height.svg): Too high causes flagging and loops; too low drags and breaks thread.
- [Hooping layers](https://easydigitizer.com/troubleshooter/img/hooping.svg): Firm, flat and square — the root of most puckering and registration faults.
- [Caps: frame and sequence](https://easydigitizer.com/troubleshooter/img/cap-frame.svg): Cap frame set-up, centre-out sewing and safe sew height.
- [Cleaning and oiling points](https://easydigitizer.com/troubleshooter/img/maintenance-points.svg): Daily and weekly care points on a multi-needle head.

---

Part of the EasyDigitizer embroidery machine troubleshooter: https://easydigitizer.com/troubleshooter/ · Agent playbook: https://easydigitizer.com/troubleshooter/agent.md · Not affiliated with any machine maker; the machine's own manual takes priority. Design-related sew-out problems (density, underlay, pull compensation): https://easydigitizer.com/help